Search Our Custom Fasteners

Thursday, August 31, 2023

Custom Tapered Shoulder Socket Head Bolts

 

Custom Tapered Shoulder Socket Head Bolt Manufacturers
These custom tapered shoulder socket head bolts were manufactured using 4140 alloy steel material with 28-32 HRC hardness and zinc clear finish.  The shoulder diameter tapers form 0.78" down to 0.75" and the head diameter was set to 1.00 +/-.015".  Underneath the shoulder approximately .55" of 3/8-24 2A thread was rolled with thread relief allowance of roughly .085".  

Custom Drilled Hole Grade 10.9 Carriage Bolts

 

Custom Drilled Hole Grade 10.9 Carriage Bolt Manufacturers
These custom carriage bolts were produced to our customer's drawing to class 10.9 characteristics with black oxide finish.  Approximately 27MM of M10-1.5MM 6G thread was rolled underneath the square shoulder and a 3MM hole was drilled through one side of the shoulder.  The square shoulder was produced to 10MM across the flats. Under the head a R45 radius was maintained to match the mating washer.

Tuesday, August 29, 2023

Custom Grade 5 Rounded Hex Nuts

 

Custom Grade 5 Rounded Hex Nut Manufacturers
These custom grade 5 hex nuts were manufactured with both sides rounded to match the mating fitting internal radius.  Production was done with cold forming process and parts were made to a 17MM across the flats dimension and an overall height of 14MM at the maximum.  M10-1.5 6H thread was tapped with a standard chamfer on each side.  Commercial zinc clear finish was run to complete the parts, with accompanying bake.  

Monday, August 28, 2023

Custom 3/8-24 Slotted Alloy Steel Lock Nuts

 

Custom 3/8-24 Slotted Alloy Steel Lock Nut Factories
These custom slotted lock nuts were manufactured using 4140 alloy steel material heat treated to 28-32 HRC.  A 5% taper on the shoulder was required which created some difficulties in modifying the cold heading equipment to meet the required tolerances.  The outside diameter was set to 1.00" and the tapered shoulder reaches 0.75" at its minimum.  Parts were run through black oxide process as the final step in the production process.

Monday, July 31, 2023

Custom T651 Aluminum Precision Machined Anodized Washers

 

Custom T651 Aluminum Precision Machined Anodized Washers
These custom precision machined washers were manufactured for our electronics customer using 6061-T651 aluminum material with a flash hard anodize finish.  The ID was set to 1.015-1.005" and OD at 1.625".  One of the corners required a R.062 machined radius and the washer thickness had to be between .125" and .135".  Full certs were provided with the parts.

Monday, July 10, 2023

Custom Socket Drive Partially Threaded Electronics Studs

 

Custom Socket Drive Partially Threaded Electronics Stud Manufacturers
We supplied these custom socket drive partially threaded studs to our electronics customer in 316 stainless steel material with plain finish.  A cold formed socket 3MM hex drive was incorporated on the threaded side and M6-1.0 thread was rolled to a length of 26MM.  The unthreaded side measures 19MM in length and 4MM in diameter with slightly chamfered corners.  

Custom Black Injection Molded ABS Spacer Blocks

 

Custom Black Injection Molded ABS Spacer Block Manufacturers
These custom black injection molded parts were manufactured using recycled ABS material in black for our specialty OEM customer.  They were manually cutting sections of long rods on the production floor prior to our supply of the custom sized part to save time and overall cost for the application.  Dimensionally the parts measured .25" at square cross section and .50" in overall length, with slightly rounded edges. 

Monday, June 26, 2023

Custom Grade 8 Torx Round Head Bolts With Black Zinc

 

Custom Grade 8 Torx Round Head Bolts With Black Zinc Finish
These custom grade 8 round head bolts were manufactured for our automotive customer to Grade 8 specification with black zinc finish.  Black zinc finish is always tricky for the grade 8 parts because it requires a bake process to limit risk of hydrogen embrittlement.  The bake process creates slight imperfections in the plating which is more apparent with the black.  The head was cold formed with T50 torx drive and the approximately 3 inches of 7/16-20 was rolled.  A .37" X .20" dog point was incorporated at the end with rounded corners.

Thursday, June 22, 2023

Custom Grade 8 Automotive Countersunk Hex Flange Bolts

 

Custom Grade 8 Automotive Countersunk Hex Flange Bolt Manufacturers
These custom grade 8 countersunk hex flange bolts were manufactured for our automotive after market manufacturing customer with zinc yellow finish.  Partial 1/2-13 thread was rolled and the length under the hex (inclusive of the countersunk portion) was set to 2-3/4".  Full certs were made available with the parts.

Wednesday, June 21, 2023

Custom Grade 8 Torx Flat Head Dog Point Screws

 

Custom Grade 8 Torx Flat Head Dog Point Screw Manufacturers
These custom grade 8 flat head screws were manufactured for our automotive aftermarket component manufacturing customer - the dog point was incorporated to allow for better ease of use and the finish was plain thermal black oxide.  5/16-18 thread was rolled with an overall length (including the head height) of .875".  Certs were made available upon request but no PPAP was required for this application.