Custom Galvanized Anchor Bolts - A36 Steel, Galvanized

These custom galvanized anchor bolts were manufactured domestically with a rush timeline using A36 steel material with a galvanized finish.  7 inches of 1"-8 coarse thread was incorporate on the long leg, with cut thread as opposed to a rolled alternative.  Overall length was set at 17" and the length of the short leg on the outside is 3".  Two galvanized nuts and washers were supplied per anchor bolt.

Custom Low Profile Torx Machine Screws - 18-8 Stainless Steel

These custom low profile torx machine screws were manufactured domestically using 18-8 stainless steel material, at production volume of approximately 5,500 pieces.  T10 size 6 lobe drive was incorporated and the head diameter at .262" +/-.01" and head height at .263" +/-.01.  6-32 thread was selected for the .185" of thread, followed by a lead point measuring .090" +.000/-.002 in diameter and .050" +.020/-.000 in length.  Parts were passivated per MIL QQ-P-35 Type II to complete the production process.

Large Custom Round Spacers In Stainless Steel Material

These large custom round spacers were manufactured domestically using 18-8 stainless steel material with plain finish - no passivation was required either for these specific parts.  The outside diameter was set at 1-1/2" +/- .01" and the inside diameter at 1/2" +/- .01".  Overall length measured 2" with the same tolerance as the other dimensions.  Slight chamfer was added on both sides to smooth out the sharp edges.  

Custom Long Compression Springs In 17-7PH Material - 30.331 Overall Length

The production of these custom long compression springs in 17-7PH material was run at a relatively small batch of only 25 pieces.  17-7PH material was used per AMS 5678 and all production work was done domestically with all secondary processes done with NADCAP certified facilities.  A first article inspection report (FAIR) was provided as well with the parts together with all other certs.  .060 +/-.0015" diameter wire was used to make this part and the ID/OD was set to .78"/.90".  Parts were passivated per AMS 2700, method 1, type 2 or 8 with full certs to complete the production process spanning approximately 7-8 weeks from start.

Custom Precision Steel Pins - 1018 CRS Material

These custom precision steel pins were manufactured domestically for our customer involved in water treatment product manufacturing.  1018 CRS material was used with plain finish.  The drive-less head measures .060" in height and .290" for the diameter, +/-.005".  The shoulder portion was the most critical with a diameter of .195" +/- .001" and a slight 45 deg by .02" chamfer.  Overall length of the shoulder shaft was set to .460".  Production is typically done at 5,000 pieces at a time.

Custom Internally & Externally Threaded Studs - Medium Carbon Steel Material

Production of these custom internally and externally threaded studs was run at approximately 10,000 pieces, in medium carbon grade 5 equivalent steel material.  The specific hardness requirement was set to 25-35 HRC.  The custom threaded studs had an overall length of .75" +/.02" with a 45-50 degree tapered point on one side.  Slotted drives were incorporated at both sides for optimal flexibility in our customer's application.  1/2-13 thread was rolled on the outside and 1/4-20 thread tapped all the way through.

Custom 17-4PH Dowel Pins - 5MM X 22.8MM In DFARS 17-4PH Material

These custom 17-4PH dowel pins were manufactured domestically at 6,000 pieces.  DFARS 17-4PH stainless steel material was used, per AMS5622 with H900 heat treatment required.  Overall length was 22.8MM +0/-.4 and the critical diameter of the pins measured 5MM +0/-.013.  Our internal part number for this custom dowel pin is 12901978 and typical lead time is 12-14 weeks from order confirmation.

Custom Flange Nuts In 17-4PH Stainless Steel Material

These custom flange nuts were manufactured domestically using 17-4PH stainless steel material with 10-24 internal thread.  Overall height of the flange nut was .19" +/-.01" and the diameter of the flange was a critical dimension at .330" +.000/-.015".  The hex was set to .250" +.000/-.005" across the flats.  Our internal part number is NRNS-10-117-4 and typical lead time for full production is 6-8 weeks from order confirmation.

Custom Binding Post - Female In 316 Stainless Steel Material With 6Lobe (Torx Alternative) Drive

These custom binding posts were manufactured using 316 stainless steel material, with 3/8 coarse internal thread tapped as close to the head as possible and a T30 drive cold headed all the way through.  The head diameter is 1.13" head height at .19" +/- .01".  The shoulder outside diameter is set to .63" and measures .75" in length, with both dimensions also limited to a +/-.01" tolerance.  4340 alloy steel material was also considered as an alternative, offering greater strength when heat treated than the 316 stainless steel material version pictured here.

Custom Low Head Slotted Machine Screws - 8-32 X .375" In 12L14 Steel

These custom low head slotted machine screws were manufactured domestically using 12L14 steel material and then run through a commercial black oxide process.  Length under the head was set at .375" +/-.03", fully threaded with 8-32 thread pitch.  The head height was set at .055", diameter at .265", slot width at .05", and slot depth at .042".  Our internal part number for this item is MSF-0806-AF and while lead time varies quite a bit depending on production volume required, we typically budget 6-8 weeks from order confirmation.