Custom 316 Stainless Steel Threaded Studs

This is another 5/8-11 threaded stud made using 316 stainless steel material, at 10" lengths.  Similar to the 6" version discussed in the previous entry these studs were also made with a 1 week lead time.  The quantity was higher however, at 150 pieces total at 10" lengths.  Higher quantities can be set up for annual or 6 month blanket purchase orders as well.

Custom 5/8 X 6 Threaded Studs in 316 Stainless Steel

We supply our customer base a large variety of custom made threaded rod studs made using 316 stainless steel.  This particular 5/8 X 6 threaded stud, with coarse thread, was supplied at a quantity of 100 pieces with a lead time of approximately 1 week.  The threaded studs are cut from 10 foot 316 stainless material and then chamfered on both ends for optimal use.

Custom Stainless Steel Shim Washers

This is one of the number of shim washers we carry, all of which are made domestically in the USA.  It's dimensions are 2.198 on the inside diameter, 2.647 on the outside diameter, and thickness of .060.  Tolerances on these custom stainless steel shim washer inside and outside dimensions is +/- .010 inches, and +/-.004 on the thickness.  All of the special shim washers we currently carry are supplied to our customers on a annual blanket purchase order basis.

Custom Square Low Carbon Steel Washer

This is the third component of the thee piece assembly shown below that we supply our customer on a blanket purchase order basis.  It is manufactured overseas using Q195 low carbon steel material, with plain and light oil finish.  Approximately 1.96" across both directions, this square washer is .600" thick with a tolerance of +/- .06".

Custom Glass Bead Nylon Insert (Thin Pattern) Lock Nuts

These special made thin pattern nylon insert lock nuts comprise three different sizes we sell to our long time customer on an annual blanket purchase order basis - the sizes covered are 1/4-28, 3/8-24, and 5/16-24.  The parts are made overseas with our long time trusted factory source and are put through a glass bead, aluminum oxide and oil treatment prior to further inspection and shipment to our customer.

Special Grade 8 Mold Bolt

This is a special 3/4-10 thread mold bolt made using Grade 8 40 CR material, with plain and light oil finish.  It is supplied in combination with the coupling nut and washer as shown below.  Sold on an annual blanket purchase order basis, this part is made overseas with our long time trusted factory source and is provided with all necessary paperwork/certs.

Custom Grade 5 Coupling Nut

This is a special Grade 5 coupling nut that is used together with a special mold bolt and square washer pictured below.  It measures 3/4-10 by 1-1/2 inches in length, and can be supplied with plain and light oil finish or hot dip galvanized finish as pictured here.  Together with the other two components, this coupling nut is supplied on a blanket as-released order basis.

Special Inconel Rolled Pin

We supply a number of version of this special pin made using Inconel alloy C-276 material in the USA.  The part is stocked and released as needed to our long time customer.  The inconel materal is hot rolled, pickled, and annealed - the final pins shown here measure 1/16 X .850".

Special to Print Grade 5 Hex Head Cap Screw With Black Oxide Finish

We supply approximately 20,000 pieces of this custom grade 5 hex cap screw annually on an as-released basis to our long time customer.  The parts are made in the USA and measure 5/16-24 X 7/8.  With the black oxide finish typical lead time for parts like this hex cap screw is approximately 5-6 weeks from order.

Special 5/8-18 Nickel Plated Palnut For Aerospace Applications

This is a 5/8-18 palnut that we supply on a blanket purchase order basis to one of our aerospace customers.  Per their specific specifications we have the plain steel version of this part nickel plated to QQ-N-290, with copper strike.  Parts go through a 5 hour pre-bake process and also an 8 hour post-bake process at 375 degree Fahrenheit.  To our customer's request all passivated and plated parts are shipped with a NADCAP cert.