Custom 316 SS Bent Anchor Rods - Per AMS 5648

These are custom 316 SS bent anchor rods per AMS 5648 we provided our aerospace customer.  130 pieces were domestically produced with a lead time of 4-5 weeks.  Material certs, First Article Inspection Report (FAIR), and a certificate of conformance was provided with the parts as well.  1/4-20 thread was incorporated at 2.25" in length, with the long leg overall length measuring at 5".  Additional detail on the anchor is below as a reference:

Custom Knurled Shoulder Bolts - 41L40 Material With Zinc & Clear Finish

These custom knurled shoulder bolts are the result of the tests we ran with different knurling methods mentioned in one of the previous posts.  Parts came out perfectly but we did run into some challenges with the lead times, being behind initial expectations due to tooling delays early in the process.  We had to throw money at expediting every part of the process where possible to try to limit our delays as much as possible - some sleepless nights worrying about these bad boys and our customer's dire need.  Every good factory and secondary processor across the nation is absolutely swamped so make sure to buffer lead time expectations as much as possible.

Custom Stainless Double End Studs - 1/2-13 Double End Studs In 304 Stainless Steel Material

These are custom stainless double end studs we provide our long time customer on a recurring basis, typically with production runs of approximately 300 pcs.  They are made domestically using 304 stainless steel material.  Pictured here is the threaded stud with it's mating part.  The thread on one side measures .875" in length and approximately .687" on the other.  The unthreaded shoulder is 1/2" diameter and the overall length of the stud is set at 2-3/8".

Custom Automotive Hardware - Regulator Vented Plug In Grade 5 Material With Level III PPAP

These custom regulator vented plugs are a perfect example of the large number of custom automotive hardware components we supply our customer base.  We worked with the customer through a number of design iterations to forgo an initial design that included a brazed component and instead go towards a design shown here with a vented hole.  The socket recess provided another challenge - going with a broached alternative would provide a better cost profile but add risk of excess material affecting the vented hole.  Instead we decided to take on the additional cost and run a cold headed process for the recess, providing a clean look and application to the part.

Custom Large Plain Steel U-Bolts - Round 3/4-10 Diameter In Variety Of Sizes

These are 9 different custom large plain steel u-bolts we supplied our customer in the Kansas City, MO area.  Quantities ranged across the nine different sizes but all shared the 3/4-10 diameter and thread pitch, as well as the plain A36 steel material.  The largest size pictured with Leonid here measured 42 inches on the inside width and 39-1/16 on the inside length.  8 inches of 3/4-10 thread was incorporated on each side.

Custom T304 Stainless U-Bolts - 1/2 X 24-9/16 Round U-Bolts

These are custom T304 stainless u-bolts we supplied our customer in two different dimensional variants: the smaller round u-bolts measure 3-1/2" for the inside width and 6-1/2" for the inside depth while the larger version measures 6-5/8" at the inside width and 10" for the inside depth.  130 pieces of the larger u-bolts and 80 pieces of the smaller variant were provided to our customer, with a lead time of 4-5 business days from order confirmation.  Material certs were made available upon request.

Custom Slotted Reverse Drive Machine Screws - 1/4-20 X 1" In Zinc Plated Steel Material

These are custom slotted reverse drive machine screws made domestically in the USA using low carbon steel material with commercial zinc and clear finish.  Approximately 12,000 pcs were produced with a lead time of 8-10 weeks.  The heads were cold headed and the slotting was done as the last stage in the process prior to zinc plating.  Material certs and certificate of conformance was made available to the customer as needed.

Custom Dog Point Screws - 10/24 X 5/8 Socket Head Cap Screws In 18-8 Stainless Steel With Half Dog Point

We have been supplying our long time OEM customer with these custom modified parts for many years.  They are 18-8 stainless steel socket head cap screws with a half dog point.  Flatness of the point is most critical to our customer's application and the process had to be refined over the first few years to get it absolutely right.  The half dog point dimensions are based on ASME B18.3-2003.

Custom Automotive Flat Socket Machine Screw - 1/4-28 X 1/2 In Grade 5 Steel Material With Thread Lock Patch & Level III PPAP

These are custom automotive flat socket machine screws we supply our aftermarket automotive OEM customer.  Parts are manufactured domestically with production runs of 5,000 pcs and lead time of approximately 8-10 weeks.  Cold headed 5/32 hex drive is incorporated with fully threaded 1/4-28 body and 60 degree countersink angle.  3/32 of hex key engagement is required and nylon thread lock patch is added to finalize the parts.  Level III PPAP was provided to the customer with the parts.

Custom Large 316 Stainless U-bolts - 1/2 X 18" Round Custom U-bolts With 4 Hex Nuts Each

These are custom large 316 stainless u-bolts we supplied our customer in San Diego.  They specialize in waterworks related construction and specifically needed 316 stainless steel material with a fast turnaround.  We were able to ship the parts within 4 days of order confirmation.  1/2" diameter bar stock was used with 2 inches of coarse thread on each leg, with inside width measuring 16.25" and inside length at 18".