Custom Thin 10-32 Zinc Plated Hex Nuts

 

These custom hex nuts were manufactured using low carbon steel material per ASME B18.2.2 with zinc clear finish.  The thin height of the nuts were set to .094" +/- .005" and across the flats dimension to a 3/8" hex.  Standard chamfers were incorporated with light chamfer on both sides of the tapped holes.

Custom 1020 Steel Precision Machined Step Pins

 

These custom precision machined stepped pins were manufactured using 1020 steel material with the larger diameter set to .156" +/-.001 and the smaller diameter at .092" +/-.002.  The overall length measured 1.09" +/-.01 and the point incorporated a radius of R.078.  Material certs were provided with the parts per customer requirements.

Custom Alloy Steel Metric Cone Point Set Screws

 

These custom alloy steel metric cone point set screws were manufactured in alloy steel material with M12 - 1.75 rolled thread and 60MM length underneath the cold formed square head.  The square head measured 13MM X 13MM X 12MM in height.  The cone point incorporated a 9MM diameter shoulder to assist in assembly on the production floor.

Custom M3 X 0.5MM Stainless Steel Shoulder Socket Bolts

 

These custom stainless steel shoulder bolts were manufactured in 18-8 stainless steel material for our drone manufacturing customer.  M3 X 0.5MM thread was rolled with a thread relief machined below the 4MM X 5MM shoulder.  A 2MM hex drive was broached at the head and a precision machined profile was incorporated on the head to meet drawing requirements.  

Custom Precision Machined Weld Studs

 

These custom precision machined weld studs were manufactured in mild carbon steel material with eventual copper flash plating prior to use on the production floor.  Overall length of the weld stud is 20.02mm and the single projection measures .75mm diameter by .80mm length.  UNC-2B thread was rolled on the threaded section and samples were manufactured for our customer to test prior to full production.

Custom Stainless Steel Chamfered Dowel Pins

 

These custom stainless steel dowel pins were manufactured in lengths ranging from 2-1/2" to 9" and a diameter of 1/8".  304 stainless steel material was used and the pins were factory passivated after the chamfer was applied on each side.  

Custom Cl 10.9 Torx Drive Socket Head Bolts

 

These custom torx drive socket head bolts were manufactured using class 10.9 steel material with a cold formed head and T20 drive combined with rolled partial 10-32 thread.  Overall length under the head was set to 1.125" +/-.01" and commercial black oxide finish was processed to complete the parts for our customer's use.  Full certs were provided with the parts.

Custom Metric Stainless Steel Standoffs

 

These custom metric stainless steel standoffs were manufactured using 303 stainless steel material with M3 X 0.5 tapped to a depth of 8MM on one side and unthreaded drilled hole on the other side at a diameter of 4.2MM and a depth of 10MM.  The flat machined sections were set to 7MM across the flats and the round outside section was at a radius of 8MM.  Full certs were provided with the parts.

Custom Low Profile Socket Head Screws in Stainless Steel

 These custom low profile socket head screws were manufactured using 304 stainless steel material for our gun product manufacturing customer and were also provided with black oxide finish.  Full 10-32 thread was rolled at a length of .75" below the cold forged head.  Parts were provided with full certs per our customer's requirements.

Custom 316 Stainless Left Hand Jam Nuts

 

These custom domestic left hand 1/2-20 thread jam nuts were manufactured in the USA using DFARS compliant 316 stainless steel material to AN316C8L requirements.  The hex nuts were passivated per AMS QQ-P-35 with our NADCAP certified facility and proof load tested per FF-N-836E.  Full certs were provided with the parts per customer requirements.